Image Acquisition	Global shutter with simultaneous integration and readout Near-IR performance provides NIR QE greater than 35% Multiple cameras on the same 1394 bus automatically sync Auto exposure control ensures optimal auto settings of shutter and gain for each image Faster standard frame rates up to 60 FPS Partial image Format_7 modes for fast frame rates and higher sensitivity Trigger modes 0 and 3 Gain and brightness control via a 10-bit A/D converter
Image Processing	On-chip 10-bit A/D provides 10-bit linear or 12-bit to 10-bit companded data 1394 timestamp embedded in image pixels
Camera and Device Control	Broadcast settings to all cameras on the same bus Non-volatile storage of camera default power-up settings Absolute value controls for shutter and gain Strobe output with configurable delay and duration Firmware upgradeable in field via IEEE-1394 interface.

• Two (2) microlens holders (with and without IR filter) and one (1) 6mm microlens
• 2 meter, 6-pin to 6-pin, super slim and flexible IEEE-1394 cable
• IEEE-1394 OHCI PCI Host Adapter 3 port-400 Mbps card
• CS-mount lens holder with 5mm spacer for use with C-mount lens
• Male GPIO connector pre-wired for quick and easy access
• Tripod mounting adapter
• FlyCapture SDK (C/C++ API and device drivers) CD

• Processor
  • Recommended – Intel Pentium^® 4 2.0 GHz or compatible processor
  • Minimum – Intel Pentium III 800 MHz or compatible processor
• Memory
  • Recommended – 512 MB RAM
  • Minimum - 256 MB RAM
• AGP video card with 64 MB video memory (128 MB recommended)
• 32-bit standard PCI slot for the IEEE-1394 card
• Supported operating system
• Microsoft Visual C++ 6.0 (to compile and run example code)

FCC / CE Compliance

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off or on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.

RoHS / WEEE Compliance

This product is RoHS and WEEE compliant.

For additional information on RoHS and WEEE, click here.

Part Number	Description	Min Qty (see notes)
FFMV-03MTM-60	640x480 BW Firefly MV with 6mm microlens	5
FFMV-03MTC-60	640x480 Color Firefly MV with 6mm microlens	5
FFMV-03MTM-CS	640x480 BW Firefly MV with CS-mount lens holder	5
FFMV-03MTC-CS	640x480 Color Firefly MV with CS-mount lens holder	5
FFMV-DEVKIT	Firefly MV Development Accessory Kit	1
ACC-01-0010	Firefly MV Case Enclosure	1
Download a list of available accessories for this model
NOTES: First time users are required to purchase a Development Accessory Kit in addition to purchasing the initial camera. Individual cameras: sold in multiples of 5 cameras only. Individual Firefly MV cameras are not sold with optics.

Coming soon!